How-to

How to stop condensation on windows in a UK home

A practical checklist for wet windows: remove water, manage moisture, measure humidity and know when to ask your landlord for repairs.

By Checked and updated

On this page (7 sections)

Wipe water from the inside of the glass and sill, then use the room’s ventilation to let moisture escape. Check humidity and temperature, reduce steam at source and investigate persistent damp before choosing a dehumidifier. A machine can help manage airborne moisture, but it cannot repair a leak or a broken ventilation system.

External sources were checked on 16 November 2026. Links labelled “Ad” are advertising placements through which Drynook may earn commission once affiliate links are active.

Why the glass is wet in the morning

Condensation forms when moist air meets a cold surface. Cooking, showers, indoor laundry and breathing all contribute water vapour; a cold window gives some of that moisture somewhere to turn into droplets. CSE explains the process in its condensation, damp and mould guide.

A bedroom can therefore have wet glass even when nobody has dried washing there. Before buying anything, look at where moisture is produced, how it leaves the home and which surfaces stay cold.

First establish where the water is. This guide concerns condensation on the room-facing surface. If you cannot wipe the mist away because it is outside or within the glazing, describe that location to the landlord or window installer rather than assuming an indoor dehumidifier is the answer.

Occasional droplets and a sill that needs drying every morning are different observations. Record how often it happens, whether the water clears and whether nearby walls, curtains or corners are also affected. The pattern is more useful than a photograph of wet glass alone.

Start with this morning’s checklist

Dry the glass and sill

Use a cloth or squeegee to collect the water, then remove it from the surface. Energy Saving Trust recommends wiping condensation away. Give the sill and frame attention as well as the middle of the pane.

If you use a cloth, wring it out and dry it somewhere else: left wet in the same room, the water goes straight back into the air. Note any damaged paint, swelling or staining so you can report it accurately.

Use extraction where steam is produced

Check that the kitchen and bathroom extractors run, and use them during cooking and bathing. Do not switch off a system designed for continuous ventilation. If you do not know how the installed system should work, ask for its instructions.

In Ireland, SEAI distinguishes background ventilation from extraction in wet rooms. They serve different purposes. A bedroom window vent is not a reason to ignore a bathroom fan that no longer works.

For a renter, a helpful report is “the bathroom fan does not start when operated”, rather than “the flat feels damp”. You can report a fault without opening the fan, altering wiring or dismantling anything.

Keep steam near its source

Use lids on pans and close the kitchen or bathroom door while producing steam, with the room’s extraction operating. Keep trickle vents open and avoid covering airbricks or other ventilation openings. These are among CSE’s practical condensation steps.

In a small flat, it helps to think about the route from the source to outside. Opening a kitchen door into a colder bedroom is not the same as extracting cooking moisture outdoors. If the layout gives you no workable route, include that in a request for the ventilation to be assessed.

Make a laundry plan

Use outdoor drying when it is available and practical. If laundry must stay indoors, choose the drying room deliberately, with a way to manage the moisture. Avoid spreading a load through every room simply because each radiator has a little space.

For drying without an appliance, Shelter’s England advice sets out steps to reduce condensation. For drying with a dehumidifier, follow its own setup instructions. Meaco’s Adlaundry guidance stresses room conditions, airflow and space between garments, rather than a guaranteed drying time.

These are different drying arrangements. Do not assume that leaving the window wide open while the machine runs will reproduce a manufacturer’s closed-room result. Keep the home’s required ventilation operating and use the appliance as instructed. Our indoor laundry guide covers choosing a machine for that job.

Check heating and cold areas

Energy Saving Trust explains that poorly heated rooms can contribute to condensation, while leaving the heating on constantly solely to prevent damp can be costly. Aim for a heating arrangement you can sustain, and report a system that does not work properly. Its damp guidance also discusses insulation gaps and cold spots.

Do not accept an instruction to turn up the heating indefinitely as a complete investigation. A north-facing wall, a draught around damaged frames and a broken radiator are observations to include when asking for help.

Measure the room before buying a machine

A digital hygrometer measures relative humidity, usually alongside temperature. CSE’s home monitoring guidance gives 40-60% RH as an indoor aim. It is a useful reference range, rather than a pass certificate for every surface in the room.

Leave the sensor in one spot and read it at the same times each day, for example when you wake and in the early evening. If you move it between readings, you are comparing places as well as days.

Record the bedroom on waking, then again later. Add a note when washing is drying, the heating changes or a shower has just finished. You do not need a spreadsheet: a short note on your phone is enough.

Look for a pattern before deciding what to buy:

The readings help describe the problem. They cannot identify a hidden leak, assess insulation or decide who is responsible for a repair. Avoid treating a display’s smiley face as a building diagnosis.

For the first purchase, prioritise a readable display showing humidity and temperature. An accuracy claim has to come from that model’s own documentation, so our hygrometer guide names only models whose maker publishes one.

When a dehumidifier helps

Consider one when the observations point to excess airborne moisture and you need help managing a defined room or indoor drying load. Write down its intended job before browsing: “the heated spare room while laundry dries” is more useful than “the whole flat feels damp”.

Room temperature affects the technology choice. Compare compressors for normally heated spaces and investigate desiccants for colder rooms, using the exact model’s performance information. Our compressor versus desiccant guide explains the distinction.

For a single heated bedroom, compare a compact candidate such as the MeacoDry Arete One 6L with the actual moisture load. AdMeaco’s official page, checked on 16 November 2026, lists 101 W at 20°C/60% RH, extraction of 3.5 L/day at 27°C/60% RH and 6 L/day at 30°C/80% RH, a 1.8 L tank, 8 kg weight, and noise “from 32 dB”, without stating the measurement mode or distance. It also documents a night mode that turns off lights and beeps. A size label still does not establish suitability by itself.

For a heated living space and frequent laundry, the Arete Two 20L is another candidate. AdIts official page lists 207 W and 8.50 L/day at 20°C/60% RH, with 230 W in the generic power field, a 4.8 L tank and noise “from 38 dB”. Use the buying guide to compare the candidates rather than choosing from an isolated cost-per-hour advert. Electricity use needs the operating mode, running time and your own tariff.

When to ask for an investigation

A dehumidifier cannot repair water ingress, failed heating or inadequate extraction. Report an active leak, persistent damp patches, damaged finishes or recurring mould when you notice them. There is no need to wait until you have bought a sensor or completed a monitoring routine.

The government’s damp and mould guidance for housing providers in England emphasises investigating underlying causes. For mould removal and health information, use that official guidance rather than treating this window checklist as cleaning or medical advice. Drying the air does not remove established mould. Our bedroom mould guide covers cleaning, cutting moisture and when to involve a landlord.

If you rent, send a written description with dated photographs. Say where the water appears, when you first noticed it, which ventilation or heating equipment seems faulty and whether the problem returns. Ask for an inspection and a written response. Keep the messages together so you do not have to reconstruct the history later.

You could write:

Water collects on the inside of the bedroom window each morning, and the wall beside the frame is also damp. The bathroom extractor does not start when operated. I have attached dated photographs. Please arrange an inspection of the cause and confirm what work is proposed.

Adapt that example to what you have actually observed. It is a report of conditions, rather than an attempt to diagnose the building yourself.

Find the advice for your nation and tenancy

Responsibilities and reporting routes differ. These are starting points, rather than legal advice:

The Irish local authority guidance includes ventilation among the rental standards and explains how concerns can lead to an inspection. Do not assume an English reporting process or deadline applies elsewhere.

Questions that come up with wet windows

Should I leave the window on the latch overnight?

There is no single opening schedule suitable for every home. Use the installed ventilation as intended, with security, weather and the room’s heating needs in mind. If the only suggested solution is sleeping beside a permanently open window, ask for the ventilation arrangement to be assessed. Do not disable a designed ventilation system to avoid an uncomfortable draught.

Is a window vacuum enough?

It can collect water from the glass, just as wiping removes it. That deals with the water already on the surface. You still need to understand why it keeps forming; collecting a tankful each morning does not establish that the moisture source or ventilation is under control.

What if the glass dries but a wall stays damp?

Record and report the wall separately. Do not use a dry pane or an improved humidity reading as proof that the wall no longer needs investigation. Keep photographs of the affected area and describe any link with rain, plumbing use or heating changes.

Sources checked on 16 November 2026